What is the weight of a Load-Lid?

A standard Load-Lid™ weighs approximately 50-70kg.

Can I open the Load-Lid with gear on top?

The Load-Lid™ is supplied with gas stays which are at the optimum pressure for everyday use and are designed to help you open and close the lid. However, they won't hold the lid open with a load on top. This is because it would require up to 200kg's of upwards pressure to open the lid with a load on it meaning that the operator would need to pull down with 200kg's of force to close the lid again which is not physically possible.If you are carrying a Roof Top Tent and require access to the Tub, we recommend removing the locking plate on the Load-Lid™ handle so you can access the Tub through the tailgate (see below).

Can I open the tailgate when the Load-Lid is closed?

The Load-Lid™ comes standard with a locking plate under the handle which serves as an extra security measure. If required, you can remove it which will allow you to open the tailgate while the Load-Lid™ is closed. Depending on your lid model you may need to open the lid slightly to get the tailgate open.If your Ute doesn't have a central locking tailgate we recommend that you install this to provide security without the plate.

What if my Roof Top Tent and with people inside is over the 200kg rating?

The Utemaster Load-Lid™ has a dynamic load rating of 200kg, which means you can carry 200kg of gear when driving. The load rating requirement when driving is far greater than when the vehicle is parked. When the vehicle is parked, the Load-Lid™ will support the weight of 2 people inside a Roof Top Tent.

If I don't add the Central Locking accessory, can I still lock my Load-Lid?

Yes, the Load-Lid™ comes with a set of keys which allow you to lock the lid manually.

Is the Load-Lid easy to fit?

The Standard and Sports Bar Load-Lids are very easy to install and are be done without needing to drill into the tub. We recommend you check out the instructions listed further up this page so you can see how it works for your model.If you are not confident in doing this yourself we can arrange fitting through one of our resellers.

Will the Load-Lid work with my liner?

This product is only compatible with the under rail liner, not compatible with over rail liner. If it is a spray-on liner you'll have no issues fitting the Load-Lid. If you have a plastic liner that goes over the top of the Tub you may need to cut it down so the lid sits correctly and does not leak.

How hard wearing is the surface?

You can put a load directly onto the aluminium treadplate surface.Aluminium is very hard wearing and the Load-Lid™ comes standard coated in a teflon-based matte black powdercoat.Some companies claim their roller covers or plastic lids have a load rating, but be aware that just because someone can stand on it while the vehicle is parked doesn’t mean it can carry a load.

Can I take it off easily?

If you can't fit your load on top, the Load-Lid™ can easily be removed by undoing the 4x wing bolts which hold it in place.It can be done in a matter of minutes and all you'll need is a mate or two to help lift it off.This gives you the space you'll need to carry objects such as a dirt bike in your tub. Please note removal process varies from model to model, however it is still super easy.

Will the Load-Lid work with my slide-out fridge?

The Load-Lid™ sits above the edge of the Tub, so the height of the fridges you can fit is determined by the Tub depth. It is very common for customers to put fridges underneath the Load-Lid.

What can I fit under the lid?

With the Load-Lid™ there are no intrusions below the top edge of your tub. The unique raised edge profile also adds a staunch appearance, improves rigidity and reduces water pooling. The easiest way to work out what will fit under the Load-Lid (for example a fridge) is to measure from the bottom of the tub to the top edge of the tub.

What is a hard lid for a ute?

A hard lid is a solid, aluminium lockable cover that fits over the tub of your ute - protecting your gear from theft, weather, and damage. Unlike soft tonneaus or canvas covers, a hard lid is built to take a load on top, giving you more usable carrying capacity than a roller shutter. Utemaster hard lids are engineered with “strong bones” to handle the real-world punishment tradies and adventurers throw at them. Whether you're hauling tools or heading off the beaten track, a hard lid lets you carry more and keeps your gear safe, dry, and ready to go.

Volkswagen Amarok Hard Lid

Name: Volkswagen Amarok Load Lid
Brand: Volkswagen Amarok
SKU: LLX-VWB3-B-DSR

Volkswagen Amarok Load Lid

Load Lid / 2023+ (NF) / Core

$4,665.00 NZD

Volkswagen Amarok Load Lid

$4,665.00 NZD

Make

Part # LLX-VWB3-B-DSR

The Utemaster MK2 Load-Lid is a premium aluminium hard lid engineered specifically for the Next Gen 2023+ Volkswagen Amarok (NF). Constructed from lightweight aluminium, it supports 200kg on top, making it the strongest hard lid available for your Amarok. Price shown includes Destroyer Side Rails, the front mounted Load Stop is an optional add on.

Installation uses your factory tub mounting points. No drilling. No permanent modifications. If you ever sell the ute, the MK2 Load-Lid comes off clean.

Security: Heavy-duty locking system with a locking plate under the handle for an extra layer of protection. Central locking optional.
Strong Bones: 200kg dynamic, 400kg static load rating - engineered and tested for real-world conditions.
Monsoon Proof: Rain channels and full weather seals keep water out and gear dry.
Utemaster Design Stamp:Engineered to suit the VW Amarok, not a generic fit.
5-Year Warranty: Backed by Utemaster's quality guarantee. We'll make it right, no questions asked.

Compatible with the full MK2 Load-Lid accessory range including crossbars, lashing rings, load stops, bike carriers, and central locking.

Scroll down to view the available accessories for the Load-Lid.

Click the button below to download the fitting instructions for your specific model selected above.

Click the button below to download the dimensions for your specific model.

Click the button below to download the fitting instructions for your specific model.

50,000+

Operators across AU and NZ

30+ years

Of manufacturing heritage

NZ Made

Designed and built locally

5yr warranty

We guarantee our quality to be right

Hard Lid Accessories

Rear Ladder Rack
The Rear Ladder Rack gives you a rear support point for carrying long loads on the...
$1087+GST
Destroyer Side Rails
The Destroyer Side Rail is built to carry. Constructed from a hybrid of pressed aluminium and...
$710+GST
Cargo Divider
A tub full of loose gear shifts, mixes, and gets buried every time you move. The...
$710+GST
Premium Light Kit
$625+GST
Cross Bars
A typical roof rack system mounted to the cab is high off the ground, making it...
$586+GST
Load Stop
Loading onto a hard lid is easy - until your gear slides straight into the rear...
$466+GST
Mule-Tek Tub Panel
Those inner tub walls above the wheel arches? Most setups just ignore them. Mule-Tek doesn't. MULE-TEK...
$417+GST
T-Track
The Load-Lid T-Track unlocks the full width of your hard lid for mounting crossbars, bike carriers,...
$373+GST
Heavy Duty Tub Mat
The Heavy Duty Tub Mat stops gear sliding around in your tub, with a 7mm thick...
$353+GST
15kg Gas Stay Upgrade
The Load-Lid comes standard with gas stays sized for opening with no load on top. If...
$200+GST
Lid Spacer Kit
The Load-Lid is designed to close flush and keep your gear secure - the Lid Spacer...
$147+GST
Tool Mount Kit
Long-handled gear rattling around in your tub is a problem the Tool Mount Kit solves for...
$126+GST
Spray Liner Seal Kit
The Next-Gen Ford Ranger has two holes at the front of the tub that allow water...
$125+GST
Mule-Fix Clamp Set
Nobody likes chasing a spade, axe or fishing rod sliding around in the back. It wastes...
$118+GST

LOAD-LID FEATURES

Strength

Dynamic Rating: This 200kg limit represents the maximum weight the lid can securely carry while you are driving or off-roading.

Static Rating: This 400kg limit represents the maximum weight the lid can support when parked, making it perfect for safely supporting items like a heavy rooftop tent and its occupants.

Monsoon Proof

There’s nothing worse than arriving at your destination to find your gear soaked. Rain channels and full weather seals to keep water out and gear dry.

Security

Keep your gear secure with the Load-Lid’s heavy-duty locking system.

Built with Strong Bones

Engineered for zero failure and maximum payload is the standard every product has to meet before it ships.

Thermal testing, cycle testing, load rating, and shake testing - that's the baseline. Then we take it further. Strong Bones extreme testing pushes every product to its limits, so you never have to find them yourself.

That's the confidence behind our 5-year warranty. If it's not right, we'll make it right - no questions asked.

Strong Bones Series

Design & engineering

World Class Manufacturing

When you pay a premium, you expect premium quality. Built in our world-class New Zealand facility, every product reflects precision and care. When you see it up close, the attention to detail speaks for itself.

Premium Aesthetic

Most products on the market are made generic to fit multiple vehicle brands, this benefits manufacturers more than owners. But every Utemaster product is custom-tailored for each model. Smooth radius corners and hidden rivets - this is precision that truly matters.

QUALITY

We guarantee our quality to be right, if its not right, we'll make it right. No questions asked.

Testing

When it comes to testing, Utemaster leaves nothing to chance. Our advanced technology lets us test products in a variety of ways - so you can count on them when it matters most.

Customer Led Development

"Don't ask me, ask the customer" is a motto Utemaster live and breathe. Our products come from real world experience and feedback from customers.

No Flat Packs

Every Utemaster canopy leaves our factory fully built, fully welded, and signed off by our QC team. No flat-pack No leaks.

Customer Transformation Stories

Hear from a selection of the 50,000+ operators who trust our gear.

Allan and Jess, Explore Oz

When your setup works, everything else gets easier For five years, Allan and Jess from ExploreOz have been living full time on the road, travelling Australia with no home base...

Ethan, Top Of The Lake Guiding

When your office is in the Alps, your setup has to keep up. Down in Glenorchy, where the road runs out and the country starts getting serious, Ethan runs Top...

JE Wilds

JE Wilds' Ford Ranger Raptor hunting and fishing build showcases a purpose-built Utemaster canopy designed for fishing trips, off-road adventure and family excursions. With a worldwide fanbase that follows along...

Load-Lid Frequently Asked Questions

: A standard Load-Lid™ weighs approximately 50-70kg.
: The Load-Lid™ is supplied with gas stays which are at the optimum pressure for everyday use and are designed to help you open and close the lid.

However, they won't hold the lid open with a load on top. This is because it would require up to 200kg's of upwards pressure to open the lid with a load on it meaning that the operator would need to pull down with 200kg's of force to close the lid again which is not physically possible.

If you are carrying a Roof Top Tent and require access to the Tub, we recommend removing the locking plate on the Load-Lid™ handle so you can access the Tub through the tailgate (see below).
: The Load-Lid™ comes standard with a locking plate under the handle which serves as an extra security measure. If required, you can remove it which will allow you to open the tailgate while the Load-Lid™ is closed. Depending on your lid model you may need to open the lid slightly to get the tailgate open.

If your Ute doesn't have a central locking tailgate we recommend that you install this to provide security without the plate.
: The Utemaster Load-Lid™ has a dynamic load rating of 200kg, which means you can carry 200kg of gear when driving. The load rating requirement when driving is far greater than when the vehicle is parked.

When the vehicle is parked, the Load-Lid™ will support the weight of 2 people inside a Roof Top Tent.
: Yes, the Load-Lid™ comes with a set of keys which allow you to lock the lid manually.
: The Standard and Sports Bar Load-Lids are very easy to install and are be done without needing to drill into the tub. We recommend you check out the instructions listed further up this page so you can see how it works for your model.

If you are not confident in doing this yourself we can arrange fitting through one of our resellers.
: This product is only compatible with the under rail liner, not compatible with over rail liner. If it is a spray-on liner you'll have no issues fitting the Load-Lid. If you have a plastic liner that goes over the top of the Tub you may need to cut it down so the lid sits correctly and does not leak.
: You can put a load directly onto the aluminium treadplate surface.

Aluminium is very hard wearing and the Load-Lid™ comes standard coated in a teflon-based matte black powdercoat.

Some companies claim their roller covers or plastic lids have a load rating, but be aware that just because someone can stand on it while the vehicle is parked doesn’t mean it can carry a load.
: If you can't fit your load on top, the Load-Lid™ can easily be removed by undoing the 4x wing bolts which hold it in place.

It can be done in a matter of minutes and all you'll need is a mate or two to help lift it off.

This gives you the space you'll need to carry objects such as a dirt bike in your tub. Please note removal process varies from model to model, however it is still super easy.
: The Load-Lid™ sits above the edge of the Tub, so the height of the fridges you can fit is determined by the Tub depth. It is very common for customers to put fridges underneath the Load-Lid.
: With the Load-Lid™ there are no intrusions below the top edge of your tub. The unique raised edge profile also adds a staunch appearance, improves rigidity and reduces water pooling. The easiest way to work out what will fit under the Load-Lid (for example a fridge) is to measure from the bottom of the tub to the top edge of the tub.
: A hard lid is a solid, aluminium lockable cover that fits over the tub of your ute - protecting your gear from theft, weather, and damage. Unlike soft tonneaus or canvas covers, a hard lid is built to take a load on top, giving you more usable carrying capacity than a roller shutter. Utemaster hard lids are engineered with “strong bones” to handle the real-world punishment tradies and adventurers throw at them. Whether you're hauling tools or heading off the beaten track, a hard lid lets you carry more and keeps your gear safe, dry, and ready to go.

Your cart is empty